This pack meets the most common needs for attaching the GoShell case in boats, planes, 4x4s, canoes etc. It offers reliability and flexibility of fixing, and does not require any installation or drilling (especially useful for rental). The double suction cup mounting ensures a very good hold and allows the Go Surface to be located in the best place. The quick-clip system allows the Surface Go to be attached / removed with one hand, useful during manoeuvres or for the control of tricky passages (harbour entrances, anchorages etc).
For Microsoft surface Go only
You can click on the components of the package to see detailed descriptions.
Waterproof and shockproof shell for Microsoft Surface Go, Go 2 and G o3
Very high level of protection and durability
The GoShell™ shockproof waterproof case is Andres Industries' first foray outside the Apple world for its range of tablet covers. It is based on the concept of its predecessors, their workmanship and durability, and offers an unequalled level of protection and performance for Microsoft Surface Go tablets (compatible with Surface Go, Go 2 and Go 3).
The GoShell™ case consists of two rigid plastic half-shells hinged on a stainless steel shaft. Watertightness is ensured by an O-ring (replaceable) held in compression by the various locks placed on the periphery. The case does not suffer any wear and tear when opened/closed repeatedly: simply place the shelf in the case and close the locks again in a few seconds.
An ultra-transparent film is placed in front of the screen, which is attached to the case. With exceptional quality and durability, it provides the same touch sensitivity as the bare screen, while protecting the latter. In case of damage, it can be easily replaced. This film is glued on its periphery by a powerful seal guaranteeing watertightness at this level.
The case also gives access to the 3 side buttons, the headphone socket and the charging slot without having to take the Surface Go out of its case. Similarly, the front and rear cameras remain perfectly usable, and openings with waterproof membranes are provided for the brightness sensor and the speaker.
Underneath the case, 4 non-slip feet (replaceable) are present. In addition, 4 screw inserts allow direct installation of a RAM accessory such as a RAM-202 base. As an option, 4 inserts in VESA format are available. Drill holes are also provided for the installation of safety screws to prevent unauthorized opening of the housing.
Finally, 7 side notches allow the installation of various accessories, some of which are supplied with the case: non-slip rubber pads to place the shelf safely on its edge & pen holder.
This case has a wide range of accessories for its demanding use on the move. It is 100% compatible with the 10" aiShell bracket (and therefore can be mounted on a tube or suction cups like the aiShell cases), as well as with the aiShell strap and rear handle.
Other devices are provided which will allow it to be recharged without fear even in the presence of water, dust, mud, etc. The main accessory is the Car Cradle, a device that ensures both holding and charging in all conditions. It is made up of a quick clamp, positioned on an articulated arm, and a special waterproof connector that is attached to the case.
In addition, a waterproof cable similar to the aiShell cable is also available.
Other accessories are also planned in the near future, including a charging rack allowing simultaneous recharging of 10 shelves.
QuickSnapper for aiShell Pro 10.5 waterproof cases
"Clip-on" bracket for aiShell Pro 10.5 waterproof case for iPad Pro 10.5"
Very useful accessory when it comes to grasp your iPad Pro 10.5" Case on the fly (to see some details on a map for exemple) and put it back immediately with one hand.
The bracket provides a 100% reliable mount even in case of repeated shocks and vibrations. (4x4; navigation etc.)
The QuickSnapper may be directly screwed on any flat surface or wall. However we do recommend to place it on an articulated arm for better readability. The arm can be fixed on suction cups, or on a tube mount.
And in case you have a handstrap or shoulderstrap already attached at the back of the case, you can still use the bracket !
Short length arm with 2 round bases
Very strong
Can be oriented at 360°
Articulated arm with 2 ball-and-socket joints allowing the tablet to be oriented in all directions.
The clamping knob and rubber-coated balls ensure excellent effortless blocking. The knob also makes it easy to disassemble the arm if needed.
Rubber coating helps absorb vibrations (MTB, 4x4 etc)
The plates can be screwed to any support, or assembled with other RAM accessories. Moreover they are compatible with most of the brackets and cradles sold on our site, allowing to create complete fixings for iPad in boat, 4x4 etc (see our value packs case + mount)
- intermediate piece in black painted aluminium (marine quality) 6.2 cm long (4.4 cm ball centre distance)
- 2 rubber coated aluminium balls diameter 2,5cm, with predrilled round plates, diameter 6,25 cm
Powerful suction cup base to attach various RAM accessories
This is a new design of the double suction cup mount, which is more compact and has a metal plate
Powerful suction cup adapter base with 2 locking suction cups.
Great to fix the iPad on a boat with no screws (e.g. on a rental boat)
Even if air goes into one cup, the other one has usually enough grip for Andres' iPad case (it is however recommended to check holding at regular intervals).
Allows the attachment of RAM-B accessories, notably the short or mid-length arms sold on this website. See demo video (of previous model)
Material : black marine aluminium plate
(crossed = previous model)
distance between suction cup centers : 14.5 cm 11.5cm
suction cup diameter : 8.5 cm
Height : 6.5 cm 4.5cm
Weight : 270 g 285g